Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
- 11. Automatic Transmission
   11.2. The terms, the accepted reductions and abbreviations
   11.3. The general description of transmission
   11.4. The basic knots of a transmission
   11.5. Methods of localisation of leaks of a working liquid
   11.6. Check of level of a working liquid in transmission 4T40
   11.7. Diagnostics of malfunctions of knots of transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




11.7. Diagnostics of malfunctions of knots of transmission
THE GENERAL DATA

Transmission noise

• Noise of chain transfer – the howling or roaring noise, which level increases or decreases at change of frequency of rotation of country houses of the engine. Noise is absent at dispersal of the car with a small corner of opening ДЗ and in an engine operating time on a place at inclusion in a transmission of ranges D (Movement) or R (Backing).

• Noise of the main transfer – the rumble, which level depends on speed of movement of the car. The rumble is swept especially up at dispersal of the car with small degree of opening ДЗ and during movement накатом with the released pedal of an accelerator.

• Noise of planetary transfer – howling noise which is most strongly shown on 1st transfer and transfer of a backing and depends on speed of the car. Noise of planetary transfer can decrease or vanish at transmission switching on an adjacent higher step.

• pump Noise – the howling sound of a high-pitch tone increasing with growth of turns of the engine. Pump noise can be audible on all transfers.

• hydrotransformer Noise – howling noise which is usually audible only on the motionless car at inclusion in a transmission of ranges D (Movement) or R (Backing). Noise ГТ increases with growth of turns of the engine.

High or low pressure of a working liquid in the trunk main

It is checked with the help densitometer (all switchings occur roughly or too slowly).

Possible codes of malfunctions:

– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 712 Gauge of temperature of a working liquid of transmission – a signal low voltage
– 713 Gauge of temperature the worker of a liquid of transmission – a signal high voltage
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 748 ЭМК a pressure regulator – refusal of an electric chain
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norm
– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)
– 1871 Wrong transfer number
– 1887 Relays of pressure of a friction clutch of blocking ГТ

TO CHECK UP THE REASON
Level of a working liquid Too high or low level to finish level of a working liquid to norm

The valve of a regulator of pressure, spring and бустерный the valve

Valve jamming
ЭМК a pressure regulator Liquid leak, damage of sealing rings
Easing of fastening of a socket, damage of pins
Pollution
The regulator valve on loading (twisting moment) of the engine Valve jamming
Transmission electroconducting Easing of fastening of a socket, short circuit
The block of the relay of pressure Easing of fastening of a socket
Damage or absence of sealing rings
The filter of a working liquid Contamination or damage of a filtering element, easing of fastening of the filter
   – Filter consolidation Leak of a working liquid
Heat exchanger pipelines Забивание section through passage or deformation of pipelines

The hydropump
Breakage, jamming, porosity of the case or leak
Shaft of a drive of the hydropump Breakage
Safety valve Spring breakage, absence of a ball
Carter of transmission, the control panel transmission, the distributive panel Porosity crankcase, leaks from a highway
Infringement of planeness of interfaced surfaces

Infringement of accuracy or sequence of the moments of switching

Possible code of malfunction:

– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – неустой чивый or a chaotic signal
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
–756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norms

TO CHECK UP
THE REASON
ЭМК switches
Pollution
Unstable rupture or chain short circuit
The gauge of position throttle заслонки
Breakage or detachment

Unstable rupture or chain short circuit

Gauges of speed of the car and speed of rotation of an entrance shaft
Breakage, detachment or fastening easing

Unstable rupture or chain short circuit

Rough gear change

TO CHECK UP
THE REASON
Pressure in the trunk main
High pressure of a working liquid
Ball return valves

Absence, is not present an inclusion delay

Демпферы inclusions of transfers
Piston or spring jamming, damper does not operate
Valve jamming damperа
Stopper of the case and the ball valve in gathering

Закупоривание

Backing transfer, slipping of frictional knots on backing transfer does not join

TO CHECK UP THE REASON
Friction clutch of transfers of a forward course
Absence of inclusion, friction clutch slipping

   – The piston in gathering with consolidation

Jamming, presence of cracks, leaks of a working liquid
   – Internal consolidation
Zakuporivanie apertures
   – Friction clutch disks
Deterioration of overlays, breakage шлицевых teeths
   – A spring ring
Displacement from normal position
   – The case
Presence of cracks, закупоривание highways
   – A stopper of the case and the ball valve in gathering
Absence or displacement from normal position
   – A spring
Jamming
Highways of a supply of a working liquid in a piston cavity of a friction clutch
Leak of a liquid or high resistance to a liquid stream
 – A support of a conducted asterisk
Porosity presence, leak through sealing rings, damage or закупоривание highways
   – The distributive panel and a lining, the control panel and linings
Porosity presence, mixture from normal position, перетечка liquids between channels, high resistance to a liquid stream
Tape brake of transfer of a backing and 1 transfer, сервоцилиндр
There is no inclusion, slipping
   – The piston
Breakage, jamming
   – Piston consolidations
Leak of a working liquid
   – A rod and a spring
Jamming
   – A cover сервоцилиндра
Breakage, easing of fastening leak of a working liquid
   – A brake tape
Breakage, deterioration, displacement from normal position

   – A pin

Breakage
   – Hydraulic highways
Breakage, deformation, закупоривание, absence of sealing rings, leaks of a working liquid
   – Carter of transmission
Porosity, leaks of a working liquid or high resistance to a liquid stream
Mechanical drive of the switch of ranges
Detachment, displacement
Zolotnik of the switch of ranges
Detachment, displacement
The ball return valve 1 (LO/PRN)
Absence
Level of a working liquid
Low level
Pressure of a working liquid

The first transfer, slipping of frictional knots on the first transfer does not join

Possible code of malfunction:

– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain

TO CHECK UP THE REASON
Friction clutch of transfers of a forward course
Absence of inclusion, friction clutch slipping

   – The piston in gathering with consolidation

Jamming, presence of cracks, leaks of a working liquid
   – Internal consolidation
Zakuporivanie apertures
   – Friction clutch disks
Deterioration of overlays, breakage шлицевых teeths
   – A spring ring
Displacement from normal position
   – The case
Presence of cracks, закупоривание highways
   – A stopper of the case and the ball valve in gathering
Absence or displacement from normal position
   – Springs
Jamming
МСХ braking by the engine
Breakage, проворачивание
МСХ 1st transfers
Breakage, проворачивание
Highways of a supply of a liquid to a piston cavity of a friction clutch of transfers of a forward course
Leak of a liquid or high resistance to a liquid stream
   – Tubes of a supply of a liquid
Deformation, breakage, leak through a sealant ные rings, закупоривание
   – A support of a friction clutch of transfers of a forward course
Porosity presence, leak through sealing rings, damage or закупоривание highways
   – The distributive panel and a lining
Porosity presence, mixture from normal position, перетечка liquids between channels, high resistance to a liquid stream
   – The block of the relay of pressure
Негерметичность consolidations of the block of the relay of pressure
ЭМК the switch And
Impossibility to include ЭМК, liquid leak
The valve of the switch of transfers 1-2
Zolotnik jamming in position of 2nd transfer
ЭМК the switch In
Impossibility to switch off ЭМК, закупоривание a drain aperture
Zolotnik and mechanical drive of the switch of ranges
Mixture of a zolotnik from normal position
The hydrotransformer
Проворачивание МСХ reactor GT
Pressure of a liquid in the trunk main
Low pressure

The second transfer, slipping of frictional knots on the second transfer does not join

Possible code of malfunction:

– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor

TO CHECK UP
THE REASON
Friction clutch of 2nd transfer
Absence of inclusion, friction clutch slipping
   – The piston in gathering with consolidation

Jamming, presence of cracks, leak of a working liquid

   – Friction clutch disks
Deterioration of overlays, breakage шлицевых teeths
   – A spring ring
Displacement from normal position
   – Springs
Jamming
   – A support of a conducted asterisk
Damage presence of cracks, закупоривание apertures
Highways of a supply of a liquid to a piston cavity of a friction clutch of 2nd transfer
Leak of a liquid or high resistance to a liquid stream
   – The control panel, a lining and a distributive plate, the distributive panel and linings: a support of a conducted asterisk
Porosity presence, mixture from normal position, fastening easing, high resistance to a liquid stream, a liquid overflowing between channels
МСХ 2nd transfers
Breakage, проворачивание
ЭМК the switch And
Jamming in the included position, закупоривание
The distributor and zolotnik of a gear change 1-2
Jamming in position of 1st transfer
Pressure of a liquid in the trunk main
Low pressure
Демпфер gear changes 1-2
Liquid leak through piston consolidations
Porosity of the distributive panel or crankcase
The distributor and zolotnik damperа

Jamming

The third transfer, slipping of frictional knots on the third transfer does not join

Possible codes of malfunctions:

– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain

TO CHECK UP THE REASON
Friction clutch of 3rd (direct) transfer
Absence of inclusion, friction clutch slipping
   – The piston in gathering with consolidation
Jamming, presence of cracks, leak of a working liquid
   – Disks
Deterioration of overlays, breakage шлицевых teeths
   – A spring ring
Displacement from normal position
   – Springs
Jamming
   – The case of a friction clutch and an entrance shaft
Damage presence of cracks, закупоривание apertures
   – A stopper of the case and the ball valve in gathering
Absence or fastening easing
Highways of a supply of a liquid in a piston cavity of a friction clutch of 3rd transfer
Presence of porosity displacement from normal position, easing кропления, перетечка liquids between channels, high resistance to a liquid stream
   – The control panel, linings and a distributive plate, distribute тельную the panel and a lining, a support of a conducted asterisk
   – Consolidations of a support of a conducted asterisk
Liquid leak
   – An entrance shaft
Негерметичность consolidations
Plug damage, mixture from normal position
ЗМК the switch In
Jamming in the switched off position, liquid leaks
The distributor and zolotnik of a gear change 2-3
Jamming
Демпфер gear changes 2-3
Liquid leak through piston consolidation
Porosity of the distributive panel or crankcase
The distributor and zolotnik damperа 2-3
Jamming
The ball return valve 5 (inclusions of a friction clutch 3 and transfers)

Absence

Pressure of a liquid in the trunk main
Low pressure

The fourth transfer, slipping of fractional knots on the fourth transfer does not include

Possible codes of malfunctions:

– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor

TO CHECK UP
THE REASON
Tape brake of 4th transfer and сервоцилиндр
Absence of inclusion, slipping
   – The piston сервоцилиндра
Breakage, jamming
   – Piston consolidations
Liquid leak
   – A piston and spring rod
Jamming
   – A servo-driver cover
Breakage, fastening easing, liquid leak
   – A tape
Breakage, deterioration, displacement from normal position
   – Carter
Crack about a tape arm
Highways of a supply of a liquid to сервоцилиндру
Porosity, displacement from normal position, fastening easing, the big resistance to a liquid stream, liquid leak between channels
   – The valve case, a lining and a distributive plate, the distributive panel, crankcase
ЭМК the switch And
Jamming in the switched off position
The distributor and zolotnik a rekey ния transfers 3-4
Jamming
Zolotnik of the switch of ranges
Displacement from normal position (in position of a range 3)
Демпфер gear changes 3-4
Liquid leak through piston consolidation
Porosity of the distributive panel or crankcase
The distributor damperа 3-4
Jamming
Pressure in the trunk main
Low pressure

The car does not get under way from a place

TO CHECK UP
THE REASON
The hydrotransformer
Breakage of assembly ledges, destruction of welded seams

Cut of fixing bolts

Deterioration шлицев a turbine shaft
Breakage of shovels of wheels
Case cracks on welded seams
Shaft of a turbine wheel

Removal or cut шлицев

The hydropump
Jamming or breakage of plates of a rotor
Shaft of a drive of the hydropump
Breakage a cut or смятие шлицев
The filter and filter consolidation
Забивание, absence
Level of a working liquid
Low level of a working liquid
Mechanical drive of the switch of ranges
Detachment
Chain transfer, asterisks and a chain
Breakage
Planetary transfer
Breakage, absence of greasing
The main transfer
Gear wheel breakage, absence of greasing
The distributive panel and lining
Damage, liquid leak, displacement from normal position
The control panel, a lining and a distributive plate
Damage, liquid leak, displacement from normal position
МСХ and a friction gear of a forward course. МСХ 1st transfers

Damage, проворачивание

Deterioration of dynamics of the car

Possible codes of malfunctions:

– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain

TO CHECK UP
THE REASON
Level of a working liquid
Low level of a liquid
ЭМК gear changes

Both ЭМК are switched off, the car gets under way on 2 transfer

ЭМК the switch In it is not switched off
System of blocking ГТ
Jamming in the included position or incomplete deenergizing of a friction clutch of blocking ГТ
The hydrotransformer

Damage or contamination

Engine stop

TO CHECK UP
THE REASON
System of blocking ГТ
Jamming in the included position or incomplete deenergizing of a friction clutch of blocking ГТ
   – ЭМК a friction clutch of blocking ГТ
Jamming in the included position, закупорива ние a drain aperture
   – The distributor of management of a blocking friction clutch

Jamming in position of inclusion of a friction clutch

Join only 1st and 2nd transfers

Possible codes of malfunctions:

– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor

TO CHECK UP
THE REASON
ЭМК the switch In
Jamming in the switched off position, liquid leak through the valve, refusal of an electric chain
The distributor and zolotnik a rekey ния transfers 2-3
Jamming in position of inclusion of 2nd transfer
ЭМК the switch And
Jamming in included position, закупорива ние the valve, refusal electric chains

2nd join only and 3rd transfers

Possible codes of malfunctions:

– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor

TO CHECK UP
THE REASON
ЭМК the switch And
Jamming in included position, refusal electric chains, liquid leak through the valve

3rd and 4th transfers join only

Possible codes of malfunctions:

– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain

TO CHECK UP
THE REASON
ЭМК the switch In
Jamming in the included position, закупорива ние the valve, refusal of an electric chain
The distributor and zolotnik a rekey ния transfers 2-3
Jamming in position of inclusion of 3rd transfer

Range P (parking) does not join

TO CHECK UP
THE REASON
The mechanism of inclusion of blocking of a target shaft
Bend or rod damage
Breakage or spring jamming
Detachment of a rod from the stopper lever
Roller and spring
Easing of an inhaling of a bolt
Bend or damage
The stopper lever
Damage, fastening easing (absence of a pin of a rod)
Zolotnik of the switch of ranges
Displacement from normal position, deformation of a drive of the lever of a stopper
Cogwheel, the blocking mechanism
Damage of teeths or шлицев
Stopper
Damage, breakage of teeths
Stopper spring
Breakage, absence
Drive of the mechanism of blocking
Adjustment infringement

Noise of a gnash of teeths

TO CHECK UP
THE REASON
Stopper
Damage, easing or detachment of a returnable spring

Inefficient braking by the engine on all ranges

TO CHECK UP
THE REASON
Friction clutch of braking by the engine
Absence of inclusion, slipping
   – The piston and consolidation
Jamming, cracks of leak of a liquid
   – Disks
Deterioration of frictional overlays, breakages шлицов
   – Springs
Jamming
   – The case and an entrance shaft
Damage, cracks, закупоривание channels
   – A stopper of the case and the ball valve in gathering
Absence or fastening easing
Highways of a supply of a working liquid to a piston cavity of a friction clutch
Porosity, mixture from normal position, fastening easing, resistance to a liquid stream, liquid leak between channels
   – Linings of the control panel and a distributive plate, distribute тельную the panel and a lining, a support of a conducted asterisk
Liquid leak
   – Consolidations, a support of a conducted asterisk
Негерметичность consolidations
   – An entrance shaft
Damage or displacement from normal position of the plug
Level of a working liquid and pressure in the trunk main
Low pressure or level
The distributor and zolotnik of a gear change 3-4
Zolotnik jamming in position of 4th transfer
Zolotnik of the switch of ranges and its drive
Displacement from normal position

Inefficient braking by the engine in a range 2

Possible codes of malfunctions:

– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)

TO CHECK UP
THE REASON
Friction clutch of braking by the engine
Absence of inclusion, slipping
Tape brake 4 transfers
Absence of inclusion slipping
The block of the relay of pressure
Liquid leak, the relay it is not efficient

Inefficient braking by the engine in a range 1

Possible codes of malfunctions:

– 1810 Malfunction of the switch of the control of ranges (the block of the relay of pressure)

TO CHECK UP
THE REASON
Friction clutch of braking by the engine
Absence of inclusion, slipping
Сервоцилиндр a tape brake of 1st transfer and backing transfer
Absence of inclusion, slipping, absence of inclusion of a tape brake of 1st transfer and backing transfer
The block of the relay of pressure
Liquid leak, the relay it is not efficient
The step-by-step return valve 1
Absence

Трогание the car at included range N

TO CHECK UP
THE REASON
Friction clutch of transfers of a forward course
It is not switched off
Friction clutch of transfer of a backing and сервоцилиндр a tape brake of 1 transfer and backing transfer
Both frictional elements are not switched off
Zolotnik of the switch of ranges and its drive
Displacement from normal position

Ranges do not join

TO CHECK UP
THE REASON
Zolotnik of the switch of ranges and drive of the lever of a stopper
Breakage, absence
Detachment from a zolotnik of the switch of ranges
Clamp of draught of a zolotnik of the switch of ranges
Detachment
Zolotnik of the switch of ranges
Jamming
Mechanical drive of the switch of ranges
Detachment
The control panel, the distributive panel and crankcase
Забивание hydraulic channels

The indicator selector position does not correspond to the chosen range

TO CHECK UP
THE REASON
Selector drive
Adjustment infringement
Spring and stopper roller
Breakage, absence
Easing of an inhaling of a bolt
Zolotnik of the switch of ranges
Detachment from the stopper lever

Leaks of a working liquid

To execute diagnostics of leak of a working liquid.

Foaming of a working liquid

TO CHECK UP
THE REASON
Working liquid
Hit in a working liquid of a cooling liquid of the engine
Too high level of a working liquid
The filter of a working liquid
Забирание
Presence of cracks
Filter consolidation
Liquid leak
Engine condition
Engine overheat
Car condition
Car overload

Vibration

TO CHECK UP
THE REASON
The hydrotransformer
Balancing infringement
Breakages of internal details
Transmission and the Engine
Displacement from normal position
Target shaft, semiaxes
Balancing infringement
Deterioration or damage of plugs
Turbine shaft
Deterioration of plugs
Balancing infringement

The friction clutch of blocking of the hydrotransformer, slipping or too slow inclusion of a friction clutch does not join

Possible code of malfunction:

– 502 Gauge of speed of the car – a signal low voltage
– 503 Gauge of speed of the car – an unstable or chaotic signal
– 703 Malfunction of the switch of a stoplight
– 712 Gauge of temperature of a working liquid of transmission – a signal low voltage
– 713 Gauge of temperature of a working liquid of transmission – a signal high voltage
– 716 Gauge of speed of rotation of an entrance shaft – low frequency of a signal
– 717 Gauge of speed of rotation of an entrance shaft – a signal is absent
– 741 Chain of management of a friction clutch of blocking ГТ, jamming ЭМК in the switched off position
– 742 Chain of management of a friction clutch of blocking ГТ, jamming ЭМК in the included position
– 751 ЭМК the switch And – the executive distributor
– 753 ЭМК the switch And – the executive distributor
– 756 ЭМК the switch In – the executive distributor
– 758 ЭМК the switch In – refusal of an electric chain
– 1560 Deviation of pressure of an electric network from norm
– 1810 Malfunction of the switch of the control of ranges (blocking of the relay of pressure)
– 1812 Overheat of a working liquid of transmission
– 1887 Relays of pressure of a friction clutch of blocking ГТ

TO CHECK UP
THE REASON
ЭМК a friction clutch of blocking ГТ
Jamming in the switched off position
Leak of a working liquid through a sealing ring
Absence of pressure on winding ЭМК
Transmission electroconducting
Bad electric contacts
Jamming wires (short circuit)
Damage of an electric socket
БУТ
Absence of operating signal ЭМК

Overheat of a working liquid

TO CHECK UP
THE REASON
The hydrotransformer
Breakage of internal details
Hydraulic system of a friction clutch of blocking ГТ
Leak of a working liquid
Hydrodistributors of management of a blocking friction clutch
Zolotnik jamming in position of deenergizing of a friction clutch of blocking
Level and pressure of a working liquid
Low level or pressure of a working liquid

The blocking friction clutch is not switched off

TO CHECK UP
THE REASON
ЭМК a friction clutch of blocking ГТ
Jamming in the included position
Закупоривание a drain aperture
Short circuit on "weight"
The hydrotransformer
Breakage of internal details
Hydrodistributors of management of a blocking friction clutch
Zolotnik jamming in position of deenergizing of a friction clutch of blocking

Premature blocking of the hydrotransformer before engine warming up

TO CHECK UP
THE REASON
The gauge of temperature of a cooling liquid of the engine
Infringement of normal work

Noise

MALFUNCTION SIGN
TO CHECK UP
THE REASON
On all ranges howling noise which depends on frequency of rotation of a shaft of the engine or disappears at blocking ГТ
The hydrotransformer
To check up that a noise source is ГТ. For this purpose at included range D to press one-times but for a brake pedal (the left foot) and a pedal of an accelerator and quickly to muffle the Engine. Noise ГТ increases at loading increase on ГТ
Howling noise of a high-pitch tone which increases at increase of turns of the engine or is sensitive to size of pressure of a working liquid
The hydropump and its drive
To check up that a noise source is the hydropump (simultaneously with pressure check in the trunk main). Pressure increase results to growth of noise of the hydropump
The sound similar to crackling of roasted corn grains
The hydropump works in a mode кавитации which is shown available vials on щупе
Liquid leak through seams of the case of the filter
Damage or mixture from normal position of consolidation of the mesh filter
Rumble or jingling sound of a high-pitch tone
Condition of pipelines of the heat exchanger of a working liquid of transmission Absence of a contact of pipelines with a surface of a radiator and with other tubes
To check up presence fluctuation of pressure the worker of a liquid on trembling of an arrow of a manometre
The howling or roaring sound amplifying and decreasing depending on speed of the car: the most appreciable at dispersal with small acceleration
Knot of chain transfer
To check up that a noise source is the chain and-or asterisks. For this purpose it is necessary to press the left foot a brake pedal and to translate the selector from range D in range R. If noise has stopped, to check up the following
Chain
Chain lengthening
Leading and conducted asterisks
Breakage or cut of teeths
Development of working surfaces of teeths
Development of an internal ring or bodies качения the needle bearing of a nave of an asterisk
Bearing damage
Noise of the main transfer (rumble), is most strongly shown at dispersal with small acceleration and-or at movement on turn
Supports of leading and conducted asterisks
Development of an internal ring of the needle bearing of a nave of an asterisk
Knot of the main transfer
Deterioration of satellites or washers
   – Gear wheels (solar, satellites) the main transfer
Damage or deterioration of teeths
The differential case
   – Semiaxial gear wheels of differential
Transmission noise on 1st, 2nd, 3rd or 4th transfer
Solar gear wheel of the main transfer
Deterioration and fatigue failures of teeths of gear wheels
   – Satellites of the main transfer
Damage of a persistent washer
Transmission noise only on some ranges
By means of the table of inclusion of frictional operating elements to track a capacity tray through a transmission in an operating mode with the raised noise and to check up the mechanisms loaded on corresponding transfers and ranges
Deterioration or damage of gear wheels