Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
- Fuel and exhaust systems
   5.2. System of injection of fuel
   5.3. Modes of functioning of system
   - 5.4. The basic knots of system
      5.4.1. A fuel tank, the pump and pipelines
      5.4.2. The distributive fuel pipeline
      5.4.3. Fuel atomizers
      5.4.4. A regulator of pressure of fuel
      + 5.4.5. The case throttle заслонки
      5.4.6. The relay of pressure of oil
      5.4.7. The relay of inclusion of the fuel pump
      5.4.8. Check of giving of the fuel pump
      5.4.9. A fuel tank
      5.4.10. An accelerator pedal
      5.4.11. The fuel filter
      5.4.12. The fuel pump
      5.4.13. Dump of pressure of fuel in system
      5.4.14. The distributive fuel pipeline
      5.4.15. Fuel atomizers
      5.4.16. A regulator of pressure of fuel
      5.4.17. The case throttle заслонки
      5.4.18. The gauge of position throttle заслонки (ДДЗ)
      5.4.19. The idling valve (КХХ)
      5.4.20. Replacement of the case throttle заслонки
      5.4.21. System of compulsory ventilation crankcase (СПВК)
      5.4.22. Check of functioning of the valve of ventilation crankcase (КВК)
      5.4.23. System of release of the fulfilled gases
      5.4.24. Katalitichesky neutralizer
      5.4.25. A reception exhaust pipe and каталитический neutralizer
      5.4.26. The forward muffler with an intermediate exhaust pipe
      5.4.27. The back muffler with an exhaust pipe
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




5.4.17. The case throttle заслонки
THE GENERAL DATA

The case throttle заслонки

 

1. THE LINING
10. THE CASE THROTTLE ЗАСЛОНКИ
13. THE PROTECTIVE CAP OF THE RESTRICTIVE SCREW OF IDLING
16. RESTRICTIVE BANDAGE OF IDLING
17. THE SPRING OF THE RESTRICTIVE SCREW OF IDLING
20. THE GAUGE OF POSITION THROTTLE ЗАСЛОНКИ
21. THE SCREW OF FASTENING ДДЗ
70. THE IDLING VALVE
72. THE SEALING RING
73. BANDAGE OF FASTENING КХХ

Replacement of details and the knots established in the case throttle заслонки, is made without dismantle from the engine of the case заслонки. However for case replacement in gathering it is necessary to remove it from the car.

To clear

PERFORMANCE ORDER
Adjournment on walls of an air line and on throttle заслонке leave by means of a cleaner for carburettors and a piece протирочной fabrics It is forbidden to use the cleaners including methyl or ethyl connections. Similar cleaners are very aggressive and are not necessary for removal of rather easy adjournment in the case throttle заслонки. Metal details can be cleared after dismantling by immersing and keeping in solvent.
The prevention

The gauge of position throttle заслонки and the idling valve should not contact to solvents or cleaners as it will lead to damage of knots.



To remove or disconnect

PERFORMANCE ORDER
1. A negative wire of the battery.
2. Partially to merge cooling liquid from a radiator to disconnect hoses from the case throttle заслонки.
3. Vacuum hoses from the case throttle заслонки.
4. Electric sockets ДДХ and КХХ.
5. An air branch pipe of an air cleaner from the case заслонки.
6. Hoses of a supply and tap of a cooling liquid from the case throttle заслонки.
7. A drive throttle заслонки from a pedal of an accelerator and a cruise-control actuation mechanism.
8. To turn out bolts of fastening of the case throttle заслонки.
9. The case заслонки together with a lining. A lining to throw out.
10. To clear details.
The prevention

At clearing of interfaced planes of details of the rests of a material of a lining it is necessary to show care.



To establish or attach

PERFORMANCE ORDER
1. The case throttle заслонки with a new lining.
2. To screw fixing bolts. To tighten fixing bolts of the case заслонки.
3. A drive throttle заслонки from a pedal of an accelerator and a cruise-control actuation mechanism.
The prevention

It is necessary to be convinced that drives throttle заслонки from a pedal of an accelerator and a cruise-control actuation mechanism allow заслонке to be closed completely.


4. Hoses of a cooling liquid to the case throttle заслонки.
5. An air branch pipe of an air cleaner to the case заслонки.
6. Electric sockets ДПХ and КХХ.
7. Vacuum hoses to the case throttle заслонки.
8. To add cooling liquid in a radiator.
9. A negative wire of the battery.

To check up

PERFORMANCE ORDER
At the idle engine completely to press and release a pedal of an accelerator for check of freedom of movings throttle заслонки.
The prevention

After installation on the Engine of the case throttle заслонки any adjustments КХХ it is not required. Position calibration запорного element КХХ is made ECU in an automatic mode after dispersal of the car till the speed exceeding 48 km/h.