Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




2.40. Piston group and rods
THE GENERAL DATA

Installation of safety tubes on шатунные bolts

1. To use short pieces of a hose in diameter of 3/8 inches as pistons directing at dismantle in gathering with rods.

To remove or disconnect

PERFORMANCE ORDER
1. To mark pistons with serial numbers of cylinders in which they were.
2. To mark rods and covers of the bottom heads that at assemblage not to mix a detail.
3. To turn a cranked shaft in position of the bottom dead point.
4. To clear adjournment of carbon (deposit) in the top part of cylinders.
The prevention

If on a cylinder mirror in a zone of the top dead point of the piston there is an appreciable fillet, it should be removed to демонта жа from the piston cylinder in gathering with a rod. For this purpose it is necessary to take advantage шабером. Not to apply больший efforts in order to avoid breakage of rings and piston damages.


5. A cover of the bottom head of a rod.
6. The piston in gathering with a rod. To push out the piston the suitable adaptation.
The prevention

To establish on шатунные bolts safety tubes, not to damage a neck of a cranked shaft, fig. Installation of safety tubes on шатунные bolts see.