Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




2.8. A final collector and a lining
THE GENERAL DATA

Final collector

AND. WIRES OF SPARK PLUGS

23. THE FINAL COLLECTOR
25. NUTS

SEQUENCE OF UNSCREWING 8–7–6–5–4–3–2–1

SEQUENCE OF THE INHALING 1–2–3–4–5–6–7–8


Heat-shielding casing of a final collector

AND. WIRES OF SPARK PLUGS
CENTURY BOLTS OF THE HEAT-SHIELDING CASING

23. THE FINAL COLLECTOR
24. THE HEAT-SHIELDING CASING


To remove or disconnect

PERFORMANCE ORDER
1. An exhaust pipe from a final collector.
2. Wires from spark plugs.
3. A heat-shielding casing 24.
4. Wires of the gauge of concentration of oxygen.
5. Eight nuts of fastening of the final pipeline in the following sequence: 8–7–6–5–4–3–2–1.
6. A final collector 23, and a lining 22.
7. Interfaced planes of a head of cylinders and a final collector.

To establish or attach

PERFORMANCE ORDER
1. A final collector 23 with a new lining 22 to screw eight nuts. To tighten nuts of fastening of a final collector the moment of 25 Nanometers (in sequence 1–2–3–4–5–6–7–8).
2. To attach an exhaust pipe to a collector. To tighten nuts the moment of 25 Nanometers.
3. A wire of the gauge of concentration of oxygen.
4. A heat-shielding casing 24.
5. Wires of spark plugs.