Daewoo Nexia

Since 1994 of release

Repair and car operation


Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




2.7. An inlet collector and a lining
THE GENERAL DATA

Inlet collector

AND. THE VACUUM HOSE OF THE REGULATOR OF PRESSURE
CENTURY THE HOSE OF THE BRAKE AMPLIFIER
WITH. THE VACUUM HOSE OF THE RECEIVER OF THE CONDITIONER OF AIR
D. THE VACUUM HOSE OF THE TANK
Е. THE VACUUM HOSE OF THE GAUGE OF PRESSURE IN THE INLET PIPELINE
F. THE HOSE OF VENTILATION OF CARTER
G. THE BLOWING-OFF HOSE OF THE TANK

53. THE INLET COLLECTOR
56. THE CASE THROTTLE ЗАСЛОНКИ

SEQUENCE OF UNSCREWING OF FIXING DETAILS 9–8–7–6–5–4–3–2–1

SEQUENCE OF THE INHALING 1–2–3–4–5–6–7–8–9


To remove or disconnect

PERFORMANCE ORDER
1. The bottom hose of a radiator.
2. To merge cooling liquid.
3. To reject aside the generator.
4. Throttle заслонку and a cable throttle заслонки from an arm of the inlet pipeline.
5. All vacuum hoses from the case throttle заслонки and the inlet pipeline.
6. Electric wires from plugs on the case throttle заслонки.
7. Fuel pipelines from the case throttle заслонки (bringing and drain).
8. A hose of system of cooling from the case throttle заслонки.
9. To turn away the top nuts, then the bottom bolts of fastening of an inlet collector, to remove washers.
10. An inlet collector 53 with a lining 52.
11. Interfaced planes of a head of cylinders and an inlet collector.

To establish or attach

PERFORMANCE ORDER
1. An inlet collector 53 with a new lining 52.
2. Fixing nuts and bolts with washers to tighten the moment of 22 Nanometers.
3. A hose of system of cooling to the case throttle заслонки.
4. Fuel pipelines to the case throttle заслонки (bringing and drain).
5. Electric wires to plugs on the case throttle заслонки.
6. All vacuum hoses to the case throttle заслонки and to an inlet collector.
7. Throttle заслонку and a cable throttle заслонки to an arm of an inlet collector.
8. The generator.
9. The bottom hose of a radiator.
10. To fill in cooling liquid.