Daewoo Nexia

Since 1994 of release

Repair and car operation

Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
- Steering
   12.2. The general description
   12.3. The reechnyj steering mechanism in gathering
   12.4. Tips of steering draughts
   12.5. Steering draughts
   12.6. A casing crankcase the steering mechanism
   12.7. Муфта a steering shaft
   12.8. A sealing cover of an aperture of a forward board of the Body
   12.9. Плунжер рейки
   12.10. The Shaft-gear wheel
   12.11. Рейка
   12.12. The needle bearing
   12.13. The directing plug рейки
   12.14. Check of neutral position рейки
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added a working liquid
   12.17. Removal of air from hydrosystem
   12.18. The steering mechanism with the hydraulic booster in gathering
   12.19. Hoses and pipelines
   12.20. A tank
   12.21. Tips of steering draughts
   12.22. Steering draughts
   12.23. Plugs of hinges of steering draughts
   12.24. Муфта a steering shaft
   12.25. A sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring плунжера
   12.28. Consolidations of a shaft of the hydrodistributor and the top bearing
   12.29. The steering mechanism
   12.30. Check of neutral position рейки
   12.31. A belt of a drive of the pump
   12.32. A pulley of a drive of the pump
   12.33. The pump in gathering
   12.34. Control levers on a steering column
   12.35. A steering wheel
   12.36. The ignition lock
   12.37. A steering column
   12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)
   12.39. Lever the switch, a steering shaft, a steering column (regulated)
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

12.28. Consolidations of a shaft of the hydrodistributor and the top bearing

THE GENERAL DATA

Consolidations of a shaft of the hydrodistributor and the top bearing

AND. BEARING ZAPRESSOVAN IN THE PLUG. CONNECTION DISMANTLING IS MADE ONLY IN NEED OF BEARING REPLACEMENT

4. THE SPRING RING
5. CONSOLIDATION (ПЫЛЬНИК) THE SHAFT-GEAR WHEEL
6. INTERNAL CONSOLIDATION OF THE SHAFT-GEAR WHEEL
7. THE BEARING IN THE PLUG
21. THE NUT
24. THE CAP

To remove or disconnect

PERFORMANCE ORDER

1. The steering mechanism in gathering. Fig. of Reechnyj the steering mechanism with the hydraulic amplifier see.

2. A counternut 16 from a stopper 17.

3. A stopper 17 from crankcase 55.

4. A spring 18, плунжер 14 with a sealing ring 15 from crankcase.

5. A spring ring 4 from a flute crankcase 55.

6. A cap 24 from crankcase 55.

7. Keeping a shaft in motionless position, to turn away a nut 21 from a shaft-gear wheel.
The prevention
Otvorachivanie nuts 21 without shaft-gear wheel fixing can lead to breakage of teeths of a gear wheel of the helmsman механиз ма. By means of a press to press a carving shaft of a shaft-gear wheel and выпрессовать from the bearing 22 neck of a shaft.

Carrying out of full dismantle of a shaft-gear wheel in gathering with the distributor is not required.

8. Пыльник 5, internal consolidation 6 and the bearing 7 from crankcase 55.

To establish or attach

PERFORMANCE ORDER

1. The distributor in gathering 10 in crankcase 55.

2. Keeping a distributor shaft, to screw a nut 21 on a shaft-gear wheel.
The prevention
Keeping a distributor shaft in motionless position, to tighten a nut 21 moment of 30 Nanometers. The inhaling of a nut 21 without shaft-gear wheel fixing can lead to breakage of teeths of a gear wheel of the steering mechanism.

3. A cap 24 in crankcase 55.

4. The top bearing 7 on a shaft of the distributor and in a nest crankcase 55.

5. Protective cap J-34614 on a distributor shaft.

6. Consolidation 6 and пыльник 5 on a protective cap in crankcase 55.

7. A spring ring 4 in a flute crankcase 55.

8. To grease литиевой консистентной with greasing плунжер 14, a sealing ring 15, a spring 18 and an adjusting stopper 17.

9. Плунжер 14 with a sealing ring 15, a spring 18 and an adjusting stopper 17 in crankcase 55.

10. Having established рейку in average position, to wrap clockwise an adjusting stopper 17 against the stop in crankcase. Then to turn away a stopper on 30–40 degrees. Проворить size of the moment of a friction on a shaft of the steering mechanism. The maximum size of the moment of a friction from a preliminary tightness of a spring плунжера should not exceed 1,8 Nanometers.

11. To screw a counternut 16 on a stopper 17. Keeping a stopper, to tighten a counternut the moment of 70 Nanometers.

12. The steering mechanism in gathering on the car.