Daewoo Nexia

Since 1994 of release

Repair and car operation

14.10. The top support

THE GENERAL DATA

Adaptations for spring compression


The bearing of the top support of a spring rack


Arrangement of a support of a spring


To remove or disconnect

Dismantle of protective caps


Removal pinа


Dismantle of the spherical hinge


Semiaxis dismantle


Dismantle of the bearing of the top support

PERFORMANCE ORDER

1. To lift the car and to remove a forward wheel. 2. A protective cap. 3. Скобу a disk brake and to fix it. (The brake drive remains thus tight). 4. To establish holder КМ-468 by means of two bolts on a wheel nave. To use bolts of fastening of a wheel. 5. To remove pin and to turn on корончатую a nut of fastening of a semiaxis. 6. Выпрессовать a finger of the spherical hinge from the rotary lever of a rack by means of stripper КМ-507В. 7. Выпрессовать a finger of the spherical hinge of the bottom lever from подшипниковой support by means of stripper КМ-507В. 8. To take out manually полуось from a wheel nave. If it is impossible, follows выпрессовать полуось by means of a nave stripper, having mounted it in position for выпрессовывания. 9. To fix полуось on weight. The prevention After semiaxis dismantle it is forbidden to load a wheel and to touch the car from a place as it can lead to axial displacement of an internal ring of the bearing. If it is necessary to roll the car, it is necessary to establish temporarily in a nave a carving coupler and to tighten корончатую a nut. (Thus position of rings of the bearing will be fixed). 10. To turn away a nut of the top support of a rack and to remove a rack in gathering. 11. To establish adaptations KM-465A and КМ-329А for compression of a spring of a forward suspension bracket on the assembly stand or a workbench where it is possible to fix the basis for installation of adaptations. The hook with a blue label should settle down at level of a yellow label on an adaptation framework. 12. To fix a rack in the adaptation. 13. To check up position of hooks. To compress a spring. 14. Keeping from rotation a rod амортиза тора racks, to turn on with the help накидного a wrench a nut of the top support. It is recommended to use available in sale bilaterial накидной a key with the big displacement of a head. 15. To dismantle from a shock-absorber rod the top support of a rack in gathering with the bearing.

To establish or attach

Installation of a spring rack in the adaptation


Installation of protective caps

PERFORMANCE ORDER

1. To grease the ball-bearing with greasing for bearings. The top support of a spring rack has not folding design and is delivered only in gathering with the ball-bearing. 2. To put on the top support and washers And, In a shock-absorber rod. The tarelchataja washer And should be located under a support the unbent edge upwards. This metal washer carries out a role of mobile consolidation of the ball-bearing at the expense of contact of edge of a washer to an external ring of the bearing. The washer In is put on a rod from above support. 3. The ledge on a spring support serves as a reference point at rack installation. If to look in a direction of movement of the car, the ledge on a support of the left rack should settle down in front, and on a support of the right rack – behind. 4. To wrap a nut of fastening of a rack накидным a key. To use only a new self-stopped nut. To tighten a nut the moment of the recommended size. At a nut inhaling to keep from rotation a shock-absorber rod. 5. To release a spring. 6. To establish a rack on the car, to fix in a nest the top support of a rack. To tighten nuts the moment of the recommended size. To use only new self-stopped nuts. 7. To insert полуось in шлицевое an aperture of a nave of a wheel and to screw корончатую a nut. To use only a new nut and a washer. Before installation to grease Slots трансмиссионным with oil. 8. To attach the spherical hinge to подшипниковой to a rack support, to tighten a nut the moment of the recommended size. To establish a spring clamp. To use only new корончатую a nut and a clamp. 9. To attach the spherical hinge of steering bent for to the rotary lever of a rack. To tighten a nut the moment of the recommended size. To use only a new self-stopped nut. The prevention In the wheel bearing should not be люфта. 10. Semiaxis installation to execute as follows. 10а. To insert полуось into a nave and to tighten корончатую a nut (with a washer) the moment of 100 Nanometers. Preliminary to attach to a nave holder КМ-468 for deduction of a nave from rotation. 10б. To release корончатую a nut of fastening of a semiaxis and then to tighten its moment of 20 Nanometers. 10в. To tighten a nut of fastening of a semiaxis on 1/4 turns. 10г. If the nut cut does not coincide with an aperture under pin in a semiaxis shaft, the additional tightening of a nut is forbidden. In this case it is necessary to release a nut before aperture coincidence under pin with a nut cut. To fix a nut pinом. 11. To fix bracket a disk brake on подшипниковой to a rack support. To tighten carving connections by the moment рекомендуе wash sizes. Preliminary to cover new bolts with fixing structure (if bolts have no special covering). To pass a carving nest a tap of M 12 х 1,5. 12. By means of assembly adaptation KM-404-A and КМ-404-С to put on against the stop protective caps on bracket a disk brake. To use new caps. 13. To tighten bolts of fastening of wheels in a cross order the moment of the recommended size.