Daewoo Nexia

Since 1994 of release

Repair and car operation

15.3. Kardannye shaft in gathering

THE GENERAL DATA

Fastening of the top support of a rack to the Body

101. NUTS of FASTENING of the TOP SUPPORT of the RACK. The MOMENT of the INHALING of 30 Nanometers.

The adaptation for a coupler of rings of the bearing

AND. EXTERNAL DIAMETER 40 MM CENTURY INTERNAL DIAMETER 20 MM 501. THE BRAKE DISK 502. THE NUT 503. THE WASHER 504. THE BOLT IN LENGTH 100 MM

Spring ring

3. THE SEPARATOR 5. BALLS 6. THE SPRING RING 10. THE SHAFT

To remove or disconnect

Nut of fastening of a semiaxis in a nave


Dismantle of the spherical hinge from подшипниковой rack support

7. THE COLLAR 8. THE COVER 10. THE SHAFT

Dismantle of a finger of the spherical hinge from the rotary lever of a rack


Dismantle of a semiaxis from a wheel nave

AND. THE NUT CENTURY THE BOLT WITH. THE PERSISTENT BEARING 401. THE WHEEL NAVE

Dismantle propeller a shaft from crankcase transmissions

8. THE COVER 10. THE SHAFT

PERFORMANCE ORDER

1. To open a cowl and to weaken nuts of the top support of a spring rack of a suspension bracket. 2. A cap of a wheel and to weaken bolts of fastening of a wheel. 3. Шплинт, a nut of a semiaxis and a washer. 4. To lift the car and to remove a wheel. 5. A spring clamp and a nut of fastening of a finger of the spherical hinge of the lever. 6. The spherical hinge of the lever by means of stripper КМ-507В. The prevention At use of stripper КМ-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", выштампованную on the adaptation. 7. A nut of fastening of a finger of the spherical hinge of steering draught. 8. The spherical hinge of steering draught by means of stripper КМ-507В. 9. To take out полуось from a wheel nave. The prevention After dismantle of a semiaxis from a nave карданный the shaft should not hang freely, keeping only on the internal hinge. It is necessary to fix the free end propeller a shaft. To place under карданный a shaft the pallet for отекания greasings. After shaft dismantle to close заглушкой an aperture in crankcase transmissions to prevent вытекание oils and dirt hit in a cavity crankcase. 10. A kardannyj shaft in gathering. The prevention After considerable run of the car (about 80-100 thousand in km) it is necessary to replace left and right карданные shaft in gathering. At assemblage it is necessary to replace a spring clamp of the spherical hinge of the bottom lever with the new. To check up, that consolidation in an aperture crankcase transmissions and the wheel bearing were pure.

To establish or attach

PERFORMANCE ORDER

1. Cautiously to insert into an aperture crankcase transmissions an internal shaft propeller a shaft 10, not to damage consolidation. To pull for the case of the external hinge for check of correct position of a shaft propeller a shaft inserted in crankcase. 2. An external shaft propeller a shaft in an aperture of a nave of a wheel. 3. The spherical hinge of the bottom lever on подшипниковую a rack support. 4. The spherical hinge of steering draught on the rotary lever of a rack. To tighten a nut of fastening of the hinge of steering draught the moment of 60 Nanometers. 5. To screw a nut on a finger of the spherical hinge of the bottom lever. To tighten a nut of the spherical hinge of the bottom lever the moment of 70 Nanometers. 6. A washer and a nut on a semiaxis shaft, strongly without tightening. To use only a new nut. 7. A wheel, having fixed bolts. Bolts strongly not to tighten. 8. To lower the car on a floor. 9. To tighten bolts of fastening of a wheel the moment of 90 Nanometers. 10. To tighten a nut of fastening of a semiaxis originally the moment of 100 Nanometers, then to release a nut and repeatedly to tighten the moment of 20 Nanometers. Then definitively to tighten a nut, having turned it on 1/4 turns. 11. To tighten nuts of fastening of the top support of a rack to the Body the moment of 30 Nanometers. 12. To fix pinом a semiaxis nut. 13. A spring clamp of a nut of the spherical hinge of the lever. 14. To fix pinом a nut of the spherical hinge of steering draught (if it is provided). 15. To finish oil level in crankcase transmissions to norm.