Daewoo Nexia

Since 1994 of release

Repair and car operation


Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
- 15. A drive of forward wheels
   15.2. The general description
   15.3. Kardannye shaft in gathering
   15.4. An external reflective ring
   15.5. A cover of the external hinge
   15.6. The external hinge
   15.7. A cover of the internal hinge of type "Tripod"
   15.8. A cover of the hinge of type "Lebro" with cross flutes
   15.9. Consolidation propeller a shaft in crankcase transmissions
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




15.7. A cover of the internal hinge of type "Tripod" To remove or disconnect

Dismantle of a spring clamp the SHRUS of type "Tripod"

 AND. THE FLAT SCREW-DRIVER

19. THE CASE THE SHRUS
20. THE SPRING CLAMP

Dismantle of a nave the SHRUS

10. THE SHAFT
21. THE SPRING RING
24. THE SPRING RING
27. ТРЕХШИПОВАЯ THE NAVE

PERFORMANCE ORDER
1. With the help бокорезов to remove collars 7, 9, fixing a protective cover 25. Collars to throw out.
2. To disconnect a cover 25 from the case 19 hinges and to shift a cover along a shaft 10, completely to open the hinge.
3. To wipe superfluous greasing with трехшиповой naves 27 and in the case 19.
4. A spring clamp 20 by means of a screw-driver, as is shown in fig. Dismantle of a spring clamp the SHRUS of type "Tripod".
5. To shift the case 19 concerning a nave 27 and a shaft 10.
6. To dissolve a ring 24 and to shift it along a shaft 10. To shift a nave 27 in the same direction, fig. Dismantle of a nave the SHRUS see.
The prevention

It is necessary to address cautiously with a nave the SHRUS. Spherical rollers and needle bearings can descend from thorns of a nave and fall.

7. To remove a cover 25 and a spring clamp from a shaft 10.
8. To wash out a cavity of the case 19 from greasing.

To establish or attach

Correct position of a spring clamp at installation

AND. EXTERNAL LEDGES

10. THE SHAFT
20. THE SPRING CLAMP
25. THE COVER

Installation of a nave the SHRUS

10. THE SHAFT
20. THE SPRING CLAMP
24. THE SPRING RING
27. ТРЕХШИПОВАЯ THE NAVE

Installation of a spring clamp the SHRUS of type "Tripod"

AND. ASSEMBLY FLUTES FOR THE SPRING CLAMP
CENTURY INTERNAL LEDGES OF THE CLAMP

10. THE SHAFT
19. THE CASE THE TYPE SHRUS "ТРИПОД"
20. THE SPRING CLAMP

PERFORMANCE ORDER
1. A small collar 9 on a mouth of a cover 25. Not to tighten a collar.
2. To put on a cover 25 a shaft 10 and to shift it into place that the small mouth of a cover has settled down over a shaft flute.
3. To tighten a collar 9 by means of clip KM-J-22610.
4. To pass on a shaft 10 spring clamp 20.
The prevention

To check up correct position of a spring clamp 20, external ledges should be turned to a shaft 10.

5. To establish on a shaft a nave and to advance it to a spring ring.
The prevention

To be convinced of that after installation the nave 27 is turned by the end of a shaft by 10 processed end face.

6. A spring ring 21 in a flute of a shaft 10 by means of a stripper for spring rings.
7. To shift a nave 27 on the end of a shaft 10 and to establish in an assembly flute a spring ring 24.
8. To enclose in a cover 25 about half of total of greasing of the hinge. With remained greasing to fill the case 19 hinges.
9. The big collar 7 on a mouth of a cover 25.
10. To pull the case 19 over a nave in gathering with the spherical rollers, established on a shaft 10, and to insert into flutes of the case 19 spring clamp 20.
11. A mouth большего diameter of a cover 25 in an assembly flute on the case 19.
The prevention

The cover 25 should not be overwound or have a fold.

12. A collar 7 on a mouth of a cover 25. To tighten a collar by means of clip KM-J-22610.