Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair leakage Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination leakage consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   - 18.27. Door-locks
      18.27.2. Door-locks of forward and back doors
      18.27.3. The internal handle of the lock - forward and back doors
      18.27.4. Draught of blocking of the lock – forward and back doors
      18.27.5. The external handle of a door-lock – forward and back doors
      + 18.27.6. The lock cylinder – forward and back doors
      18.27.7. Door-lock assemblage
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. ventilation the valve (the Body a hatch-back)
   18.35. hatch mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment




18.27. Door-locks

18.27.1. A zapornyj bolt
THE GENERAL DATA

Zapornyj bolt of a door-lock

1. ЗАПОРНЫЙ THE BOLT
2. THE ADJUSTING WASHER
3. THE FLOATING PLATE WITH THE CARVING APERTURE

The zapornyj bolt with washers is screwed in the floating plate established on a back rack of a doorway. The floating plate provides position adjustment запорного a bolt both in vertical, and in a cross-section direction. Door lock-out in the closed position occurs, when the plug of the lock is hooked by the cut with a head запорного a bolt.

Longitudinal adjustment запорного a bolt

To find out necessity of longitudinal adjustment, it is necessary to execute described below operation.
PERFORMANCE ORDER
1. To be convinced that position of a door concerning the Body is adjusted correctly.
2. To cover partially a door so that a lock plug has concerned запорного a bolt.
3. Pressing and releasing the door-lock handle, some times to cover and open a door, each time, only concerning запорного a bolt. Thus it is possible to check easily mutual position запорного a bolt and a door-lock plug. The plane of a plug of the lock should be perpendicular axes запорного a bolt and be approximately in the middle of the last (not more close 4 mm from bolt edges).
4. In need of longitudinal adjustment запорного a bolt it is necessary to screw or turn out it on the necessary distance by means of a wrench (шестигранного a core) on 8 mm. At ввертывании a bolt it is necessary to remove preliminary adjusting washers, and at вывертывании – to add washers in the thickness of 2 mm in necessary quantity.
5. To establish запорный a bolt. To tighten запорный a bolt of a door-lock the moment of 53 Nanometers.

Vertical and cross-section adjustment запорного a bolt

Increase in diameter of an aperture for запорного a bolt

1. THE ABRASIVE HEAD (THE ROUND FILE) IN DIAMETER 9,5 MM
2. THE ELECTRIC DRILL

Necessity for vertical or cross-section adjustment запорного a bolt can arise for the several reasons: deformation of the Body as a result of failure, replacement of a sealant of a door which can affect work of the lock, complaints to the raised aerodynamic noise or difficulties at opening and door closing etc. For vertical and cross-section adjustment запорного a bolt it is necessary to execute the following.

PERFORMANCE ORDER
1. To check up correctness of adjustment of position of a door.
2. To turn out запорный a bolt by means of a wrench on 8 mm.
3. The end запорного a bolt to shift a floating plate in demanded position. To screw запорный a bolt in a plate aperture.
4. If it is required to shift a plate on большее distance, than it allows an aperture for a bolt in a back rack of a door, it is necessary by means of an electric drill and наждачной a head or a round file to process an aperture, having increased its size in a demanded direction.
5. To establish into place запорный a bolt. To tighten запорный a bolt of a door-lock the moment of 53 Nanometers.