Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair leakage Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination leakage consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. ventilation the valve (the Body a hatch-back)
   18.35. hatch mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment




18.9. Glass of a back door (the Body a hatch-back) To remove or disconnect

PERFORMANCE ORDER
1. An internal cord of a sealant of glass of a back door.
2. Electric conducting of a heater of glass.
3. Молдинг glasses. At the subsequent installation new moldingа old it is possible to remove, having wrung out or having cut off it.
4. By means of a knife for sealant removal to make an incision consolidation on all perimetre as it is possible more close to a glass edge.
5. Glass of a back door.

To clear

PERFORMANCE ORDER
1. An aperture of a window from the rests of all materials.
2. Glass on perimetre of an edge for the subsequent drawing of preparatory layers.
3. To wipe a windscreen the pure fabric moistened in spirit.

To establish or attach

PERFORMANCE ORDER
1. By means of a new brush to put on edge has flown down preparatory layers, using corresponding structures from a repair set. At first it is necessary to put грунтовоч ный a layer from transparent structure, and then – from structure of black colour. Priming coats put on perimetre of an edge of glass (glass from the inside) a strip the in width of 6 mm.
2. Молдинг on glass. For fixing moldingа on glass follows, to use a sticky tape (fastens to an external surface of glass). To put on perimetre of a window aperture of a back door the platen уретанового hermetic in the thickness of 3 mm.
3. Glass in a window aperture of a back door by means of the second mechanic. To centre glass in a window doorway. Use of rubber suckers can facilitate glass installation.
4. To check up tightness of consolidation of glass of a back door, watering. At detection leakage it is necessary to dry glass and in addition to impose герметизирующий structure. If it was not possible to eliminate a leak, it is necessary to remove glass and to repeat all installation anew.
5. Electroconducting of a heater of glass (in the presence of a heater).
6. An internal cord of a sealant of glass.