Daewoo Nexia

Since 1994 of release

Repair and car operation


Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
- 10. A five-speed transmission and the main transfer RPO MM5
   10.2. The general description
   10.3. Diagnostics of malfunctions
   10.4. The possible reasons of the raised noise of a transmission
   10.5. Level check transmission oils
   10.6. Adjustment of a drive of the mechanism of switching
   10.7. The gear change lever
   10.8. The floor mechanism of management of a transmission
   10.9. Draught of the mechanism of management
   10.10. The intermediate lever
   10.11. A speedometer drive
   10.12. A cover of the mechanism of the switch
   10.13. Consolidations of semiaxes
   10.14. Transmissions in gathering
   10.15. Dismantling of a transmission and the main transfer
   10.16. Characteristic malfunctions of a transmission and the possible reasons
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




10.14. Transmissions in gathering
THE GENERAL DATA

Boltovoe fastening of transmission to the engine

AND. THE BOLT

Arrangement of the gauge of speed of the car

A. THE CABLE OF THE DRIVE OF THE SPEEDOMETER
CENTURY THE ELECTRIC SOCKET OF THE GAUGE OF SPEED OF THE CAR

Traverse for support of the power unit

 

The left arm

AND. BOLTS OF FASTENING OF THE ENGINE TO THE ARM
CENTURY THE ARM

To remove or disconnect

Dismantle of a primary shaft


PERFORMANCE ORDER
1. A negative wire of the battery.
2. An air cleaner.
3. A cable of a drive and the lever of the mechanism of deenergizing of coupling.
4. A clamp 223 and an axis 237 propeller the hinge of a drive of management of a transmission.
5. A cable of a drive of a speedometer, a socket of the gauge of speed of the car and a socket of the switch of a lantern of a backing.
6. To weaken a bolt 210 клеммового connections.
7. To turn out three top bolts of fastening of transmission to the engine.
8. To establish to a traverse.
9. To lift the car.
10. To dismantle forward wheels.
11. A grjazezashchitnyj guard.
12. To disconnect from crankcase transmissions a condenser wire (protection against electromagnetic hindrances).
13. Выпрессовать both spherical hinges from steering levers.
14. Semiaxes.
15. A cover crankcase transmissions.
16. To disconnect semiaxes from transmission.
17. To mark with a paint assembly position of a primary shaft concerning the block of gear wheels for convenience of the subsequent installation.
18. To extend a primary shaft, to remove a support.
19. To hang out the power unit.
20. To remove left forward, then left back arms of the engine and to turn out the bottom bolts of fastening crankcase transmissions.
21. To take aside and to remove transmission.

To establish or attach

Installation of a spring ring on the end of a primary shaft

AND. THE SCREW

3. THE SPRING RING OF THE PRIMARY SHAFT

PERFORMANCE ORDER
1. Before transmission installation to insert into place the right shaft as its installation later (after joining of transmission to the engine) will be impossible.
2. To screw the bottom bolts of fastening crankcase transmissions to the engine and to tighten the moment of the demanded size. The moment of an inhaling of bolts of 60 Nanometers.
3. To screw bolts of the left back arm to Tighten bolts of fastening of the engine to an arm the moment of 90 Nanometers.
4. The left forward arm and to screw bolts. To tighten bolts of fastening of a forward arm to crankcase transmissions by the moment of 60 Nanometers. To tighten bolts of fastening of an arm to a support the moment of 60 Nanometers.
5. To leave both semiaxes in crankcase transmissions.
6. To attach spherical hinges of steering draughts and to fix them.
7. Cautiously to insert a primary shaft in шлицевые apertures of the block of gear wheels and a conducted disk of coupling. For shaft installation in former position concerning interfaced details it is necessary to be guided by a label made before dismantling.
8. To screw in a shaft the screw 67. To tighten the screw of a primary shaft the moment of 15 Nanometers.
9. A spring ring 66.
10. "A mass" wire to a cover crankcase, a stopper 53 and a wire of the condenser of protection against electromagnetic hindrances.
11. A flywheel cover to screw bolts. атянуть bolts of a cover of a flywheel the moment of 7 Nanometers.
12. To screw the top bolt of fastening of transmission to the engine. To tighten the top bolt of fastening crankcase transmissions to the engine the moment of 60 Nanometers.
13. A grjazezashchitnyj guard.
14. Both lobbies of a wheel to lower the car to Tighten bolts of fastening of wheels the moment of 90 Nanometers.
15. To attach conducting to the switch of a lantern of a backing and a cable of a drive of a speedometer.
16. To attach a cable of a drive of deenergizing of coupling and to adjust a drive.
17. A negative wire of the battery.

To check up

PERFORMANCE ORDER
Oil level in transmission.
Refuelling capacity of transmission of 1,8 l. To apply oil to mechanical transmissions of mark DEUTSCH VEEDOL HD Т/М FLUID, SAE 80.