| 1. A stopper 234 from a cover of the mechanism of the switch 235. |
| 2. To turn out bolts of 226 fastenings of a cover 235. |
| 2а. To uncover 235 with crankcase 1. |
|
|
3. To attach bolts a cover 235 to an arm of KM 552. 3акрепить an arm in adjusting adaptation KM-113-2. |
4. Details of a cover of the mechanism of the switch:
– A spring ring 230;
– The plug 229;
– A spring 228;
– The intermediate lever of the switch 227;
– The plug with a finger 225 and a pin 235.
The prevention Other details are unattended and to dismantle from a cover does not follow.
|
|
5. To turn out a bolt 103 and to take out from crankcase the plug 101 drives of a speedometer. |
|
6. The switch of a lantern of a backing 88. |
| 7. To turn out bolts 54 and to uncover 51 crankcase. To include 2nd transfer. |
|
8. To turn away bolts 65, to disconnect from crankcase 1 additional crankcase 35 and to take out from crankcase together with it transmission shaft. |
| 9. To attach bolts additional crankcase 36 in gathering with shaft to arm КМ-552. To fix arm КМ-552 in установоч ном adaptation KM-113-2. |
|
10. To turn away bolts 42 and to remove a plug of inclusion of 5th transfer 44. |
|
11. A conducted gear wheel of 5th transfer 60, gear coupling the synchronizer 58 and a nave of the synchronizer of 5th transfer 56. To use stripper КМ-161А. To remove the needle bearing of 5th transfer 81, a ring 61 and both half rings 62. |
|
12. An elastic ring 63 and a leading gear wheel of 5th transfer 64. To enclose on an end face of the block of gear wheels 70 support before stripper installation. |
|
13. To turn out bolts 41 and to remove a connecting link of 5th transfer 46 together with the doggie 80. Выпрессовать a pin from a connecting link for replacement of the doggie. |
|
14. Four stoppers 33, 38. To use stripper КМ-457А and assembly adaptation KM-J-7004. Springs 34. A clamp of the mechanism of switching 35. A pin 39. A pin of the mechanism of blocking 40. |
| 15. A bolt 79 and a support 78. To establish rods of plugs consistently in position of 2nd, 5th and 3rd transfers. At inclusion of 3rd transfer the support will be pushed out. |
|
16. Pins of plugs 3/4-й transfers and backing transfers. Опереть the top ends of rods of plugs on wooden брусок in order to avoid damage of directing apertures in additional crankcase. |
| 17. Rods and plugs of inclusion of transfer of a backing and 3/4-й transfers from additional crankcase. Gear муфты inclusions of transfers should be in neutral position. |
|
18. The lever of the switch of 5th transfer from additional crankcase. |
|
19. The spring rings keeping the block of gear wheels 70 and secondary shaft 83 in подшипниковых support additional crankcase. For dismantle of fixing spring rings 31 and 69 to use assembly nippers КМ-443Д. |
| 20. A pin 40 mechanisms of blocking from an aperture additional crankcase 36. |
|
21. A secondary shaft 83, the block of gear wheels of a primary shaft 70, intermediate) a gear wheel of a backing 73, a plug 20 and a rod of 21 switchings of 1st and 2nd transfers from additional crankcase 36. |
| 22. To clamp an axis 72 intermediate gear wheels in a vice through safety overlays of sponges. For axis dismantle slightly to knock with a hammer on additional crankcase through copper выколотку. |
| 23. To turn out five bolts of fastening of the right cover 126 to crankcase. |
| 24. By means of two screw-drivers to remove with crankcase the right cover 126. |
25. To disassemble the main transfer:
– To turn out bolts 113 and to remove the pallet crankcase 112;
– To remove consolidations 107;
– To put labels of mutual position on an adjusting nut 109 bearings and crankcase;
– To turn out a bolt 106 and to remove a plate of a clamp 104;
– To turn out an adjusting nut 109;
– To take out the main transfer to gathering through the bottom window in crankcase. |