Daewoo Nexia

Since 1994 of release

Repair and car operation

16.9. Plugs of hinges of a back suspension bracket

THE GENERAL DATA

Installation and dismantle of the plug from an eye of the lever of a back suspension bracket

AND. TO CUT НОЖОВКОЙ GROOVES UNDER FACE LEDGES OF WASHER DC45001 CENTURY AT INSTALLATION TO COMBINE ARROWS ON DETAILS J29376-1 HJ29376-11 OF THE ASSEMBLY ADAPTATION WITH THE LABEL AT THE END FACE OF THE EYE OF THE LEVER WITH. THE EYE OF THE LEVER OF THE BACK SUSPENSION BRACKET 22. THE PLUG OF THE HINGE OF THE LEVER OF THE BACK SUSPENSION BRACKET 26. THE LEVER OF THE BACK SUSPENSION BRACKET

To remove or disconnect

It is necessary to replace at each dismantling at once both plugs.

PERFORMANCE ORDER

1. To lift the car and to fix in appropriate way. 2. To lift one of levers of a suspension bracket by means of a hydraulic jack and a suitable assembly support. To remove a bolt 8 and a nut 9. 3. To substitute a hydraulic jack under the second lever and to remove fastening of the shock-absorber 7. 4. To lower an a bit hydraulic jack and to dismantle a spring 28 and the top elastic ring 29. 5. To lift it is a little lever a hydraulic jack and again to attach the shock-absorber 7 to a beam 26 bolt 8. 6. To execute operations 3,4 and 5 on other party of the car. To arrange a hydraulic jack in the middle under a beam of 26 suspension brackets. 7. Fastenings to the bottom of the Body of brake pipelines. To place brake hoses and cables of a lay brake in deepening of the bottom of the Body. 8. A bolt 23 and a nut 21 from an arm on the Body bottom. If necessary to use a screw-driver as the lever to press a hinge eye. 9. To lower it is a little beam 26 back suspension brackets and to fix a bolt 23 earring from complete set КМ-158 in an arm of the hinge of a back suspension bracket. For simplification of dismantle of plugs to heat up eyes of levers to temperature 50–75 ° S.Nagrev to make hot air from a pneumatic network. 10. For dismantle of the plug from a lever eye to execute following operations. 10а. To establish adaptation KM-158 on an eye of the lever with the plug 22. 10б. To put on a bolt entering into assembly complete set КМ-158, a washer with face ledges, to insert a bolt into a plug aperture, then to put on it a persistent washer. 10в. To rest a stripper washer against an end face of the plug 22 and to screw on a bolt a nut. The prevention To cut ножовкой two grooves at an end face of the old plug 22 under ledges of a washer of a stripper. 10г. Rotating adaptation KM-158 bolt, выпрессовать the plug from a lever eye.

To establish or attach

Plug orientation at installation

And. The CORNER 45±5 22. THE PLUG OF THE HINGE OF THE LEVER OF THE BACK SUSPENSION BRACKET

PERFORMANCE ORDER

1. For plug installation in a lever eye to execute following operations. 1а. To establish adaptation KM-158 on the suspension bracket lever. 1б. To prepare and partially to collect assembly adaptation KM-158. 1в. To establish the new plug 22 on a bolt, preliminary having inserted it into an eye aperture. To turn the plug in specified in fig. plug Orientation at installation position concerning a lever eye. To expose arrows on adaptation KM-158 details according to a face label, fig. Installation and dismantle of the plug from an eye of the lever of a back suspension bracket see. 1г. To screw a nut on adaptation KM-158 bolt. 1д. Rotating adaptation KM-158 bolt, запрессовать the plug in a lever eye. At correct installation the back end face of the plug should settle down заподлицо with a lever eye. 2. To remove earring КМ-158 from an arm of a suspension bracket and to establish on a car opposite side. 3. To dismantle old and запрессовать the new plug in the second lever of a suspension bracket, operating similarly. 4. To raise a beam of a back suspension bracket by means of a hydraulic jack and to connect eyes of levers to arms of a suspension bracket bolts 23. To screw nuts 21. To lower a jack. 5. To establish the bottom buffer of a spring 27 on the lever, the top elastic ring 29 in a glass of the Body and a spring 28. 6. To lift a hydraulic jack the lever of a suspension bracket and to connect to the lever the bottom eye of the shock-absorber 7. To lower a jack, to establish a spring 28 and the shock-absorber 7 on a car opposite side, operating similarly. To lower the car. 7. To tighten bolts of fastening of a beam of a back suspension bracket in such position of levers which corresponds to a static course of a suspension bracket at the equipped weight of the car.