Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral moldings
   18.4. Diagnostics and repair leakage Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination leakage consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. ventilation the valve (the Body a hatch-back)
   18.35. hatch mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   - 18.40. A luggage carrier cover (the Body a sedan)
      18.40.1. Торсионы luggage carrier covers
      - 18.40.2. The lock of a cover of a luggage carrier
         18.40.2.1. A zapornaja loop of the lock
         18.40.2.2. The lock cylinder
      18.40.3. Door-lock assemblage
      18.40.4. A sealant
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment




18.40.2.2. The lock cylinder
THE GENERAL DATA

The lock cylinder in gathering

 
1. THE NUT (2 PIECES)
2. THE LOCK CYLINDER IN GATHERING
3. DRAUGHT
4. THE RING WITH THE LEADING LEAD
5. THE ARM
6. THE RETURNABLE SPRING
7. THE LOCK CYLINDER
8. THE LOCK CASE

The lock cylinder

1. NESTS OF SPRINGS
2. THE FIRST CUT FOR ЗАПОРНОЙ PLATES (REMAINS EMPTY)
3. ЗАПОРНАЯ THE PLATE

To remove or disconnect

PERFORMANCE ORDER
1. To turn on two nuts кропления the lock cylinder.
2. To disconnect draught from the cylinder of the lock and to remove it from a luggage carrier cover.

To establish or attach

PERFORMANCE ORDER
1. The lock cylinder in a luggage carrier cover, having attached to the cylinder draught.
2. Two nuts of fastening of the cylinder of the lock to a luggage carrier cover.
3. To insert springs of plates and запорные plates into corresponding apertures and cuts of the cylinder of the lock. Thus it is necessary to be guided by a key code.
The prevention

Not to establish a spring and a plate in the first cut of the cylinder. At installation of springs and запорным plates in the lock cylinder it is necessary to grease all details with a thin layer консистентной greasings.


4. For check of correctness of assemblage to insert into the cylinder of the lock a key. If all plates act from the cylinder, assemblage is made correctly.