Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




мдф шлифованная влагостойкая Glunz 22 мм.

3.15. A gear belt
THE GENERAL DATA

Dismantle of a gear belt

 


Arrangement of labels at correct installation of cam-shafts and a cranked shaft

 


Arrangement of labels натяжителя a gear belt

 


To remove or disconnect

PERFORMANCE ORDER
1. A forward cover 73 gear belts.
2. A pulley 157.
3. Two bolts of fastening of the steering amplifier.
4. To weaken, but not to turn out completely 3 bolts of 166 fastenings of the water pump, to take away the pump 167 by means of adaptation KM-421A and to remove a gear belt.
The prevention

To mark a direction of movement of a gear belt.



To establish or attach

PERFORMANCE ORDER
1. Before installation of a gear belt it is necessary to check up correctness of mutual angular position of camshafts and a cranked shaft of the engine.
1а. The label I on a wreath of a cogwheel And an inlet cam-shaft should settle down opposite to label Е of a cogwheel In a final cam-shaft (fig. the Arrangement of labels see at correct installation of cam-shafts and a cranked shaft).
1б. The label on a cogwheel 153 cranked shaft should be opposite to the index on a cover 155.
1в. Gear the belt should be established with preservation of a direction of movement.
1г. By means of adaptation KM-421A to take away the water pump 167 as much as possible to weaken натяжитель a gear belt, to screw and slightly to tighten a bolt of fastening of the water pump. To turn clockwise on 2 turns a cogwheel of a cranked shaft and to check up coincidence of labels (fig. the Arrangement of labels see at correct installation of cam-shafts and a cranked shaft).
1д. To turn the water pump 167 counter-clockwise so that labels And and In on the lever and an arm натяжителя have risen the friend opposite to the friend. To tighten bolts 166 and once again to check up coincidence of labels And and V.Esli labels were displaced, to repeat the described operation.
2. To tighten a bolt of fastening of the water pump the moment of 8 Nanometers.
3. The pump 58 steering hydraulic boosters on a back cover 52 gear belts and to screw in two bolts 59.
4. To tighten bolts of fastening of the pump of the steering amplifier the moment 20 Hм.
5. A pulley 157 cranked shaft.
6. A forward cover 73 gear belts.
7. To tighten bolts of fastening of a forward cover of a belt the moment of 8 Nanometers.
8. A pulley of the pump of the steering amplifier (fig. Dismantle of a pulley of the pump of the steering amplifier see). To tighten bolts of fastening of a pulley of the pump of the steering amplifier the moment of 20 Nanometers.
9. To adjust a tension of belts of the generator and the conditioner compressor.