Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




3.2. The general description
THE GENERAL DATA

The top part of the engine (1,5 l, Р4 DOHC)

 

1. THE COVER OF CANDLES
2. HIGH VOLTAGE WIRES
3. THE CENTRAL WIRE OF THE HIGH VOLTAGE
4. THE COVER OF THE JELLIED MOUTH
5. COVER CONSOLIDATION
6. THE SPARK PLUG
7. COVER КЛАПАННОГО OF THE MECHANISM
8. The Mb BOLT
9. THE BOLT
10. THE WASHER
11. THE HOLDER OF THE BUNCH OF CANDLE WIRES
12. The Mb BOLT
13. THE ARM OF FASTENING OF CANDLE WIRES
14. САПУННЫЙ THE HOSE
15. THE COVER LINING
16. THE IGNITION COIL
17. THE SCREW
18. FORWARD CONSOLIDATION OF THE CAM-SHAFT
19. THE CAM-SHAFT
20. THE PUSHER OF THE VALVE WITH THE HYDROJACK
21. PLATE КЛАПАННОЙ OF THE SPRING
22. THE VALVE CRACKER
23. КЛАПАННАЯ THE SPRING
24. CONSOLIDATION OF THE CORE OF THE VALVE
25. BOLT М8
26. THE IGNITION DISTRIBUTOR
27. THE BACK COVER OF THE BEARING OF THE CAM-SHAFT
28. SCREW M6
29. THE INTERMEDIATE COVER OF THE BEARING OF THE CAM-SHAFT
30. THE BOLT OF THE HEAD OF CYLINDERS
31. THE WASHER
32. THE FORWARD COVER OF PODSHIPNI КА OF THE CAM-SHAFT
33. THE HEAD OF THE BLOCK OF CYLINDERS
34. THE VALVE
35. THE LINING OF THE HEAD OF THE BLOCK OF CYLINDERS
36. THE HAIRPIN OF THE FINAL PIPELINE
37. THE WASHER
38. THE NUT
39. THE ELEVATING EYE
40. THE LINING
41. THE FINAL PIPELINE
42. THE OXYGEN GAUGE
43. THE LINING OF THE FLANGE OF THE EXHAUST PIPE
44. THE DUAL EXHAUST PIPE
45. THE EXHAUST PIPE HAIRPIN
46. THE WASHER
47. THE NUT
48. BOLT М8
49. THE THERMOSTAT CASE
50. CONSOLIDATION
51. THE THERMOSTAT
52. THE BACK COVER OF THE GEAR BELT
53. НАТЯЖИТЕЛЬ THE BELT
54. BOLT М8
55. THE INTERMEDIATE ROLLER
56. THE WASHER
57. BOLT М8
58. THE PUMP OF STEERING GIDROUSILITE ЛЯ
59. BOLT М8
60. THE WASHER
61. CONSOLIDATION OF THE BRANCH PIPE OF THE PUMP
62. THE GEAR BELT
63. THE CAM-SHAFT COGWHEEL
64. THE WASHER
65. THE BOLT OF FASTENING OF THE COGWHEEL
66. КОНУСНАЯ THE PLUG OF FASTENING OF THE COVER
67. THE REMOTE PLUG OF FASTENING OF THE COVER
68. THE HAIRPIN OF THE COVER OF THE BELT
69. THE ARM
70. THE WASHER
71. BOLT М8
72. CONSOLIDATION OF THE FORWARD COVER OF THE BELT
73. THE FORWARD COVER
74. THE WASHER
75. SCREW M6
76. THE ARM OF THE INLET PIPELINE
77. SCREW M8
78. SCREW M10
79. THE ELEVATING EYE
80. BOLT М8
81. PLANCK OF THE GENERATOR
82. BOLT М8
83. THE GAUGE OF TEMPERATURE OF THE COOLING LIQUID
84. THE GAUGE OF THE INDEX OF TEMPERATURE OF THE ENGINE
85. THE FUEL DISTRIBUTIVE PIPELINE
86. THE REGULATOR OF PRESSURE OF FUEL
87. THE FUEL ATOMIZER
88. BOLT М8
89. ELECTRIC WIRES OF SYSTEM OF INJECTION OF FUEL
90. THE VACUUM HOSE
91. THE LINING
92. THE INLET PIPELINE
93. THE HAIRPIN OF THE INLET PIPELINE
94. NUT М8
95. BOLT М8 WITH THE WASHER
96. THE LINING
97. THE CASE THROTTLE ЗАСЛОНКИ
98. BOLT М8 WITH THE WASHER
99. THE ARM OF FASTENING OF THE COVER OF THE CABLE THROTTLE ЗАСЛОНКИ
100. BOLT М8
101. THE CABLE IN THE COVER

The bottom part of the engine (1,5 l, Р4 DOHC)

 

111. OIL ЩУП
112. THE DIRECTING TUBE
113. THE PLUG OF THE HEAD OF CYLINDERS
114. THE BLOCK OF CYLINDERS
115. COUPLING CARTER'S PLUG
116. ЗАГЛУШКА
117. THE OIL FILTER
118. THE PLUG OF THE OIL FILTER
119. THE PLUG
120. THE STOPPER
121. THE STOPPER PLUG
122. THE BOLT WITH THE WASHER
123. THE COUPLING CASING
124. THE CONDUCTED DISK OF COUPLING
125. THE BOLT
126. THE FLYWHEEL
127. BACK CONSOLIDATION OF THE CRANKED SHAFT
128. THE CRANKED SHAFT
129. LOOSE LEAVES OF RADICAL BEARINGS
130. THE LOOSE LEAF OF THE AVERAGE PERSISTENT RADICAL BEARING
131. COVERS КОЖИНЫХ OF BEARINGS
132. THE BOLT
133. THE LINING OF THE OIL PALLET
134. THE OIL PALLET
135. THE DRAIN STOPPER
136. THE STOPPER LINING
137. THE BOLT
138. ШПОНКА
139. THE ARM AND THE BOLT OF FASTENING OF THE RECEPTION OIL BRANCH PIPE
140. THE RECEPTION BRANCH PIPE OF THE OIL PUMP
141. The Mb BOLT
142. CONSOLIDATION OF THE RECEPTION OIL BRANCH PIPE
143. STOPPER РЕДУКЦИОННОГО of the VALVE (М20х1.5)
144. CONSOLIDATION OF REDUKTSION НОГО OF THE VALVE
145. SPRING РЕДУКЦИОННОГО OF THE VALVE
146. PLUNZHER РЕДУКЦИОННОГО OF THE VALVE
147. THE OIL PUMP
148. THE BALL
149. ПЕРЕПУСКНОЙ THE PUMP VALVE
150. CONSOLIDATION
151. THE SWITCH OF THE SIGNALLING DEVICE OF PRESSURE DROP OF OIL
152. FORWARD CONSOLIDATION OF THE CRANKED SHAFT
153. THE COGWHEEL OF THE CRANKED SHAFT
154. COVER CONSOLIDATION
155. THE COVER
156. THE BOLT
157. THE PULLEY
158. THE WASHER
159. THE PULLEY BOLT
160. The Mb BOLT
161. THE GEAR WHEEL OF THE OIL PUMP
162. THE COGWHEEL OF THE OIL PUMP
163. THE COVER OF THE OIL PUMP
164. THE SCREW WITH THE SECRET HEAD
165. THE LINING OF THE OIL PUMP
166. THE BOLT WATER US THE WASP
167. THE WATER PUMP
168. CONSOLIDATION OF THE WATER PUMP
169. THE STOPPER
170. THE BRANCH PIPE OF THE COOLING LIQUID
171. ШАТУННЫЙ THE BOLT
172. THE COVER OF THE HEAD OF THE ROD
173. COMPLETE SET ШАТУННЫХ OF LOOSE LEAVES
174. THE PISTON FINGER
175. THE PISTON
176. THE COMPLETE SET OF PISTON RINGS
177. THE BOLT WITH THE WASHER
178. THE TUBE OF VENTILATION OF CARTER
179. THE COLLAR
180. THE HOSE OF VENTILATION OF CARTER
181. BOLT М8
182. THE STARTER
183. BOLT М8
184. THE STARTER ARM

The gazoraspredelitelnyj mechanism of the engine

 


Head of the block of cylinders

 


Arrangement of labels I and Е at installation of cogwheels

 

Рядный 4-cylinder, 4-taktnyj the petrol Engine of water cooling is equipped by two camshafts which are located in a head of cylinders. 16 valves (on 4 on each cylinder) are established V-shapedly. The drive of cam-shafts carries out ся from a cranked shaft a gear belt. One of two cam-shafts operates group of inlet valves, and other shaft – final valves. In a drive of valves there are hydraulic jacks of thermal backlashes.

The block of cylinders is cast from an aluminium alloy and unites four rowed cylinders. In расточках the block of cylinders pig-iron sleeves are established.

The cast head of the block of cylinders from an aluminium alloy is executed under the cross-section scheme of a purge of cylinders. Jacks of backlashes are established in a drive of each valve.

The shod steel cranked shaft leans against five radical bearings with вставны ми loose leaves. Shatunnye necks are located in one plane through 180 degrees.

The pig-iron camshaft is established on five bearings in the aluminium case which is located from above heads of cylinders. Rotation is transferred to a camshaft from a cranked shaft of the engine by means of a gear belt and a wheel established on the forward end of a cam-shaft.

The cogwheels established on both camshafts have одинако вую the form and are marked by letters I and Е (accordingly for a shaft operating inlet, and for a shaft, operating final valves).


The prevention

The new camshafts established on inlet and final valves, are interchangeable. However the shaft which were in operation, are not interchangeable.


Pistons are made of an aluminium alloy. On pistons it is established on two компрессионных and on one маслосъемному to a ring. For reduction of pressure of the piston by a wall of the cylinder during a working course of an axis of piston fingers have cross-section displacement of 0,35-1,65 mm concerning a piston axis.

In interface of a piston finger to the piston mobile landing, and with the top head of a rod – dense landing is used.

Movement is transferred to valves directly from camshaft cams. The hydrojacks established in pushers of valves, promote decrease in noise of the engine. The design of a drive of valves satisfies to hard work conditions at high frequency of rotation of the engine and allows to reduce labour input of maintenance service газораспределительного the mechanism.