Daewoo Nexia

Since 1994 of release

Repair and car operation


Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




3.36. A flywheel. Back consolidation of a cranked shaft To remove or disconnect
The prevention

Back consolidation 127 cranked shaft can be replaced without dismantle of the oil pallet or a cranked shaft.

PERFORMANCE ORDER
1. Carter of transmission.
2. Fixing bolts and a flywheel 126.
3. A casing of coupling 123 and a conducted disk of coupling (only a hand-operated transmission).
4. To take out back consolidation 127. To clear a landing nest of consolidation in the block and a condensed neck of a shaft.

To establish or attach

PERFORMANCE ORDER
1. New back consolidation 127 in a nest of the block of cylinders. To press consolidation in regular intervals on all perimetre (to use оправку J36792). For simplification of assemblage to grease an external surface of consolidation.
2. A flywheel.
The prevention

To use only new bolts.

3. To tighten bolts of fastening of a flywheel the moment of 35 Nanometers, then in addition to tighten turn on 30 °–45 °.
4. A casing of coupling 123. To tighten bolts of fastening of a casing of a flywheel the moment of 35 Nanometers.
5. A conducted disk of coupling (only a hand-operated transmission).
6. Carter of transmission.