Daewoo Nexia

Since 1994 of release

Repair and car operation



Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment




3.35. Pistons and rods To remove or disconnect

PERFORMANCE ORDER
1. The oil pallet 134, the oil pump 147, a head of cylinders 33.
2. To lower the piston 175 in the lowest position. To remove a fillet on a cylinder mirror.
3. To uncover 172 bottom heads and loose leaves 173 шатунного the bearing. Preliminary to mark details with a cylinder serial number.
4. A rod with the piston 175. Establish preliminary on шатунные bolts protective plugs. To clear an internal surface of cylinders by means of a fabric moistened in oil.

To establish or attach

PERFORMANCE ORDER
1. Pistons 175 with rods.
The prevention

Before assemblage to grease all details. To establish the piston in the assembly adaptation for compression of piston rings and to shift it in the cylinder, slightly tapping on the piston bottom.

The arrow on the piston bottom should be directed to a forward part of the engine. To establish rods on necks of a cranked shaft 128.


2. To establish loose leaves 173 шатунных bearings.
The prevention

Loose leaves, shaft and cover necks should be oiled. To use only new шатунные bolts.


3. Covers шатунных bearings.
4. To tighten шатунные bolts the moment of 25 Nanometers, then in addition to tighten turn on 30 °.
5. The oil pump 147, the oil pallet 134, a head of cylinders 33.