Daewoo Nexia

Since 1994 of release

Repair and car operation

Daewoo Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Fuel and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
- Brake system
   17.2. The general description
   17.3. Check of a technical condition of brake system
   17.4. Filling of a tank of the main brake cylinder
   17.5. Removal of air from brake system
   17.6. Washing of brake system
   17.7. Check of a regulator of brake forces
   17.8. Brake hoses (lobbies)
   17.9. Brake hoses (back)
   + 17.10. A lay brake
   17.11. Check of a condition of forward brake overlays
   17.12. Check of a condition of back brake overlays
   17.13. Brake disks
   17.14. Brake drums
   17.15. A brake pedal
   17.16. The main brake cylinder
   17.17. A tank
   17.18. Regulators of brake forces (proportional valves)
   17.19. The main brake cylinder in gathering
   17.20. Repair of the main brake cylinder
   17.21. The disk brake mechanism
   17.22. Колодки and overlays
   17.23. A protective cover of the piston
   17.24. A brake disk
   17.25. A support
   17.26. A guard
   17.27. Support repair
   17.28. The drum-type brake mechanism
   17.29. Adjustment of the brake mechanism
   17.30. Adjustment of a lay brake
   17.31. A basic brake disk
   17.32. The wheel cylinder
   17.33. Repair of the wheel cylinder
   17.34. The vacuum amplifier of brakes
   + 17.35. Antiblocking system of brakes
   17.36. Removal of air from a brake hydraulic drive
   17.37. Removal of air from a brake hydraulic drive manually
   17.38. The valve for removal of air from the block of modulators
   17.39. Electromagnetic valves of modulators
   17.40. The block of hydraulic modulators with electric motors
   17.41. The electronic block of management of braking
   17.42. The gauge of angular speed of a forward wheel
   17.43. Flexible conducting CRS of a forward wheel
   17.44. The gauge of angular speed of a back wheel
   + 17.45. Flexible conducting CRS of a back wheel
   17.46. A system electric safety lock
   17.47. Relay ABS
   17.48. Signalling devices
+ Body
+ Heating, ventilation
+ Electric equipment

17.25. A support To remove or disconnect

Dismantle of protective caps



Dismantle of fixing bolts



1. To merge two thirds of brake liquid from a tank.
2. To lift the car.
3. To mark position of forward wheels concerning naves and to remove forward wheels.
4. To drown the piston 9 in the cylinder of a brake support and to provide backlashes between overlays pads 2, 3 and a brake disk 13.
5. A bolt of fastening of the union of a brake hose, only in case of need dismantle from the car скобы for dismantling and repair. To muffle an aperture in a support and a hose in order to avoid losses of a brake liquid and hit in dirt system.
6. To weaken easy blows of a hammer on a chisel landing of protective caps 5 and to remove caps by means of a screw-driver.
7. To turn out fixing bolts 6 and to remove a support. If the support is dismantled for servicing and repair of other details, to suspend a support on a wire hook, having fixed it on a telescopic rack of a forward suspension bracket. Fastening bolts скобы on a suspension bracket rack have a special covering. To pass the M tap 12х1,5 carving apertures in an arm of a rack of a suspension bracket. Before installation to grease with a thin layer of fixing structure the new bolts which do not have a special covering.

To establish or attach

1. A support on an arm of a telescopic rack of a suspension bracket to screw fixing bolts 6. To tighten fixing bolts the moment of 95 Nanometers.
2. The union of a brake hose to a support. To tighten a hollow bolt of fastening наконечни ка a hose the moment of 25 Nanometers.
3. Protective caps of 5 heads of bolts by means of adaptation KM-404A.
The prevention

To use only new caps. Caps should sit down exactly on the places.

4. Wheels, observing initial position and being guided on the made labels.
5. To lower the car.
6. To add in a tank a fresh brake liquid and to finish its level to norm. To remove air from the support cylinder if the brake hose has been disconnected. Repeatedly to check up level of a brake liquid in a tank.
7. Some times to press a brake pedal for data pads and establishments of normal backlashes between колодками and a disk.
The prevention

It is forbidden трогание the car while the brake pedal did not become "rigid".